PSB Subseries 300 Subwoofer

PSB Subseries 300 Subwoofer

12-inch Driver Powered with 300 Watts

  • frequency response 27-150 Hz (±3dB)
  • built-in Class D Discrete MOSFET amplifier developed in partnership with NAD Electronics
  • 300 watts RMS amplifier
  • continuously variable low-pass 50-150 Hz crossover
  • 12" polypropylene woofer cone with butyl rubber surround
  • bass-reflex (ported) enclosure
  • convenient front-mounted volume and crossover controls
  • front-mounted phase switch
  • line-level/LFE inputs and outputs
  • speaker-level inputs
  • auto on/off ultra-low, energy saving <0.5W standby power consumption
  • detachable 8-foot power cord
  • 15-1/4"W x 19-15/16"H x 18-11/16"D
  • Local Warranty: 2 Years

S$ 1,080.00

Add to cart

17 other products in the same category:

Product Description

Features

PSB SubSeries: The PSB SubSeries 300 powered subwoofer is designed to provide the flattest possible frequency response, full bass extension, low distortion, and high output. The PSB SubSeries powered subwoofer is perfect for music and movie soundtracks.

Class D Discrete MOSFET Amp (from NAD): The PSB SubSeries 300 powered subwoofer employs a custom-designed Class D discrete MOSFET amplifier from NAD. The integrated digital amplifier from NAD features an automatic varying switching frequency that maintains maximum efficiency and low THD under all conditions. The Class D amplifier also incorporates proprietary limiting circuitry preventing audible overload while remaining true to the dynamics of your music or movie sound track. This circuitry combines peak limiting circuits that hold amplifier signal swing to the point just short of the amplifier's clipping, with compression circuitry that will reduce the amplifier's gain.

12" Woofer: To compliment the powerful Class D amplifier, the SubSeries 300 uses a 12" polypropylene cone woofer with rubber surround, 1.5" voice coil, and 35oz magnet. The PSB woofer is designed to reduce mechanical noise and prevent harsh sounds at extreme excursion.

Bass-Reflex Cabinet: The PSB SubSeries 300 powered subwoofer features a bass-reflex cabinet with a down-firing port for greater efficiency and bass response. The down-firing port has a large radius end that flare to reduce noise from air turbulence.

Controls

Front-Mounted Controls: Two rotary control knobs (volume/crossover) and phase switch are provided on the front of the subwoofer for added convenience. The front-mounted controls are hidden behind detachable grille.

Volume Control: The rotary volume knob controls the output level of the powered subwoofer, relative to the volume of the other speakers in the system.

Low-Pass Crossover: The low-pass crossover adjusts the high-frequency roll-off of signals sent to the subwoofer. The control is continuously variable from 50 Hz to 150 Hz, and allows you to precisely match the subwoofer's bass production with your system's main left & right stereo speakers.

Phase Switch: The phase switch allows for the adjustment of the phase of the subwoofer in relation to the speakers used in the system; either 0 or 180 degrees.

Auto On/Off: The powered subwoofer features a main power switch on the back panel. When switched to On, the subwoofer is initially in stand-by mode, awaiting the presence of an audio signal. When the signal is received, the subwoofer turns on automatically. When no signal is detected, the sub's amp will automatically turn off after approximately 15 minutes. In the Off position, the subwoofer will not power up. A green LED, located on the front panel between the control knobs, will glow when the subwoofer is active (it will glow red when off).

Connections

LFE Input/Output: A single gold-plated RCA jack (LFE) is provided for connecting the powered subwoofer to your AV receiver's LFE output. Since the subwoofer/LFE outputs are filtered by most receivers/processors, the subwoofer's variable low-pass filter is not required and is bypassed. The powered subwoofer also has an LFE output for adding additional subwoofers.

Stereo RCA Inputs: Two gold-plated RCA jacks are provided for connecting your source unit via the low-level input. If your receiver or integrated amplifier has preamp outputs, or if you are using a preamplifier without a designated subwoofer/LFE output, the preferred connection is to use a stereo RCA cable plugged into both left and right inputs. If the preamp outputs are unfiltered, the subwoofer's internal crossover should be used.

Stereo RCA Outputs: The sub also has gold-plated RCA low-level output jacks, useful if your amp has pre-out/main-in jacks, or when using a separate preamp and amplifier. The low-level output is internally processed by the sub's active crossover; the high-pass slope is 12dB/octave and the crossover point is fixed at 80Hz.

Speaker-Level Input: Two pairs of 5-way binding post terminals (for left and right channel) are provided for connecting the powered sub with speaker wire. The terminals will accept bare wire, spade lugs, pin connectors, and single or dual banana plugs.

Power Cord: The subwoofer has a removable 8' power cord with an IEC 2-pronged connector. This allows you to use a third-party IEC-type power cord, if desired.

Comments

Write your review

PSB Subseries 300 Subwoofer

PSB Subseries 300 Subwoofer

12-inch Driver Powered with 300 Watts

  • frequency response 27-150 Hz (±3dB)
  • built-in Class D Discrete MOSFET amplifier developed in partnership with NAD Electronics
  • 300 watts RMS amplifier
  • continuously variable low-pass 50-150 Hz crossover
  • 12" polypropylene woofer cone with butyl rubber surround
  • bass-reflex (ported) enclosure
  • convenient front-mounted volume and crossover controls
  • front-mounted phase switch
  • line-level/LFE inputs and outputs
  • speaker-level inputs
  • auto on/off ultra-low, energy saving <0.5W standby power consumption
  • detachable 8-foot power cord
  • 15-1/4"W x 19-15/16"H x 18-11/16"D
  • Local Warranty: 2 Years

Write your review